Saturday, September 24, 2016

Reducing Power Consumption on Arduino Zero, MKR1000, or any SAMD21 Arduino Part 1

In this multiple part series we look at how to reduce power consumption for battery powered designs that utilize Arduino's with the Atmel SAMD21 MCU (Zero, MKR1000, etc). In part one we look at how to put the SAMD21 to sleep and wake it up with either the real time clock (RTC) or an external event on an input pin.



//***************Arduino Sketch from the video*********************.
//This code was used for a tutorial on the ForceTronics YouTube channel. It shows how to save power
//by putting Arduino's based on the SAMD21 MCU (MKR1000, Zero, etc) to sleep and how to wake them
//This code is public domain for anybody to use or modify

//#include "RTCZero.h"
#include <RTCZero.h>

/* Create an rtc object */
RTCZero rtc;

/* Change these values to set the current initial time */
const byte seconds = 0;
const byte minutes = 00;
const byte hours = 00;

/* Change these values to set the current initial date */
const byte day = 24;
const byte month = 9;
const byte year = 16;

void setup() 
{
  delay(5000); //delay so we can see normal current draw
   pinMode(LED_BUILTIN, OUTPUT); //set LED pin to output
  digitalWrite(LED_BUILTIN, LOW); //turn LED off

  rtc.begin(); //Start RTC library, this is where the clock source is initialized

  rtc.setTime(hours, minutes, seconds); //set time
  rtc.setDate(day, month, year); //set date

  rtc.setAlarmTime(00, 00, 10); //set alarm time to go off in 10 seconds
  
  //following two lines enable alarm, comment both out if you want to do external interrupt
  rtc.enableAlarm(rtc.MATCH_HHMMSS); //set alarm
  rtc.attachInterrupt(ISR); //creates an interrupt that wakes the SAMD21 which is triggered by a FTC alarm
  //comment out the below line if you are using RTC alarm for interrupt
 // extInterrupt(A1); //creates an interrupt source on external pin
  
  //puts SAMD21 to sleep
  rtc.standbyMode(); //library call
  //samSleep(); //function to show how call works
}

void loop() 
{
  //do nothing in main loop
}

//interrupt service routine (ISR), called when interrupt is triggered 
//executes after MCU wakes up
void ISR()
{
  digitalWrite(LED_BUILTIN, HIGH);
}


//function that sets up external interrupt
void extInterrupt(int interruptPin) {
  pinMode(interruptPin, INPUT_PULLUP);
  attachInterrupt(interruptPin, ISR, LOW);
}

//function to show how to put the 
void samSleep()
{
  // Set the sleep mode to standby
  SCB->SCR |= SCB_SCR_SLEEPDEEP_Msk;
  // SAMD sleep
  __WFI();
}

//**********************Changed "begin" function from RTCZero Library**************
void RTCZero::begin(bool resetTime)
{
  uint16_t tmp_reg = 0;
  
  PM->APBAMASK.reg |= PM_APBAMASK_RTC; // turn on digital interface clock
  //config32kOSC();

  // If the RTC is in clock mode and the reset was
  // not due to POR or BOD, preserve the clock time
  // POR causes a reset anyway, BOD behaviour is?
  bool validTime = false;
  RTC_MODE2_CLOCK_Type oldTime;

  if ((!resetTime) && (PM->RCAUSE.reg & (PM_RCAUSE_SYST | PM_RCAUSE_WDT | PM_RCAUSE_EXT))) {
    if (RTC->MODE2.CTRL.reg & RTC_MODE2_CTRL_MODE_CLOCK) {

      validTime = true;
      oldTime.reg = RTC->MODE2.CLOCK.reg;
    }
  }
  // Setup clock GCLK2 with OSC32K divided by 32
  GCLK->GENDIV.reg = GCLK_GENDIV_ID(2)|GCLK_GENDIV_DIV(4);
  while (GCLK->STATUS.reg & GCLK_STATUS_SYNCBUSY)
    ;                                                         /*XOSC32K*/
  GCLK->GENCTRL.reg = (GCLK_GENCTRL_GENEN | GCLK_GENCTRL_SRC_OSCULP32K | GCLK_GENCTRL_ID(2) | GCLK_GENCTRL_DIVSEL );
  while (GCLK->STATUS.reg & GCLK_STATUS_SYNCBUSY)
    ;
  GCLK->CLKCTRL.reg = (uint32_t)((GCLK_CLKCTRL_CLKEN | GCLK_CLKCTRL_GEN_GCLK2 | (RTC_GCLK_ID << GCLK_CLKCTRL_ID_Pos)));
  while (GCLK->STATUS.bit.SYNCBUSY)
    ;

  RTCdisable();

  RTCreset();

  tmp_reg |= RTC_MODE2_CTRL_MODE_CLOCK; // set clock operating mode
  tmp_reg |= RTC_MODE2_CTRL_PRESCALER_DIV1024; // set prescaler to 1024 for MODE2
  tmp_reg &= ~RTC_MODE2_CTRL_MATCHCLR; // disable clear on match
  
  //According to the datasheet RTC_MODE2_CTRL_CLKREP = 0 for 24h
  tmp_reg &= ~RTC_MODE2_CTRL_CLKREP; // 24h time representation

  RTC->MODE2.READREQ.reg &= ~RTC_READREQ_RCONT; // disable continuously mode

  RTC->MODE2.CTRL.reg = tmp_reg;
  while (RTCisSyncing())
    ;

  NVIC_EnableIRQ(RTC_IRQn); // enable RTC interrupt 
  NVIC_SetPriority(RTC_IRQn, 0x00);

  RTC->MODE2.INTENSET.reg |= RTC_MODE2_INTENSET_ALARM0; // enable alarm interrupt
  RTC->MODE2.Mode2Alarm[0].MASK.bit.SEL = MATCH_OFF; // default alarm match is off (disabled)
  
  while (RTCisSyncing())
    ;

  RTCenable();
  RTCresetRemove();

  // If desired and valid, restore the time value
  if ((!resetTime) && (validTime)) {
    RTC->MODE2.CLOCK.reg = oldTime.reg;
    while (RTCisSyncing())
      ;
  }

  _configured = true;
}

Thursday, September 15, 2016

Reducing Power Consumption on the Arduino Enabled ESP8266

In this tutorial we look at how to reduce the power consumption of your Arduino enabled ESP8266 WiFi module for battery powered applications.



//**************Arduino code: ESP8266_Sleep_Example *************
/*
 This sketch was created for a tutorial on saving power using the ESP8266 with the Arduino IDE 
 That was presented on the ForceTronics YouTube Channel. This code is public domain for anybody to use
 at their own risk
 */
#include <Arduino.h>
#include <ESP8266WiFi.h> //not using WiFi but need for some of the sleep commands

const int LED_PIN = 5; // Thing's onboard, green LED
const int sleepTimeS = 5; //sets deepsleep time to 5 sec

void setup() 
{
  pinMode(LED_PIN,OUTPUT); //setup LED pin 
  flashLED(); //function that flashes LED on and off
  WiFi.forceSleepBegin(0); //this function turns on modem sleep mode (turns off RF but not CPU)
  flashLED();
  WiFi.forceSleepWake(); //wakes modem up from sleep mode
  flashLED();
  // deepSleep time is defined in microseconds. Multiply seconds by 1e6 
  ESP.deepSleep(sleepTimeS * 1000000); //Can also add mode setting: WAKE_RF_DEFAULT, WAKE_RFCAL, WAKE_NO_RFCAL, WAKE_RF_DISABLED
  //ESP.deepSleep(0,WAKE_RF_DEFAULT); //In Deep-sleep mode, the chip can be woken up and initialized by a low-level pulse
    //generated on the EXT_RSTB pin via an external IO
}

void loop() 
{ //do nothing in the loop
}

//function that flashes LED at 1.5sec intervals
void flashLED() {
  digitalWrite(LED_PIN, HIGH);
  delay(1500);
  digitalWrite(LED_PIN, LOW);
  delay(1500);
}

//**************Arduino code: ESP8266_Sleep_Cloud_Example *************
/*
 This sketch was used for a tutorial on saving power with the ESP8266 using Arduino IDE 
 That was presented on the ForceTronics YouTube Channel. This code is public domain for anybody to 
 use or modify at your own risk

 Note that this code was leveraged from a Sparkfun example 
 on using their cloud service Phant
 */
#include <Arduino.h>
// Include the ESP8266 WiFi library.
#include <ESP8266WiFi.h>
// Include the SparkFun Phant library.
#include <Phant.h>

//Set your network name and password
const char WiFiSSID[] = "YourNetwork";
const char WiFiPSK[] = "YourPassword";

//define constants for pin control and node number
const int LED_PIN = 5; // Thing's onboard, green LED
const int ANALOG_PIN = A0; // The only analog pin on the Thing
const int NODE_NUM = 1; //node identifier

//declare phant address and security keys
const char PhantHost[] = "data.sparkfun.com";
const char PublicKey[] = "YourPublicKey";
const char PrivateKey[] = "YourPrivateKey";

//specify the rate that you post data to cloud
const unsigned long postRate = 15000;
unsigned long lastPost = 0;
const int sleepTimeS = 15;

void setup() 
{
  initHardware(); //setup arduino hardware
  connectWiFi(); //Connect your WiFi network
  digitalWrite(LED_PIN, HIGH);
  while (postToPhant() != 1) //post to cloud in setup code because we will reset after sleep
  {
    delay(100);
  }
  digitalWrite(LED_PIN, LOW);
  // deepSleep time is defined in microseconds. Multiply
  // seconds by 1e6 
  ESP.deepSleep(sleepTimeS * 1000000); //This is where we go to sleep, will reset upon waking up
}

void loop() 
{ //do nothing here
}

//function used to connect to WiFi network and where we set transmit power level
void connectWiFi()
{
  byte ledStatus = LOW;
  //Set transmit power level
  WiFi.setOutputPower(0.0); //sets transmit power to 0dbm to lower power consumption, but reduces usable range
  // Set WiFi mode to station (as opposed to AP or AP_STA)
  WiFi.mode(WIFI_STA);
  // WiFI.begin([ssid], [passkey]) initiates a WiFI connection
  // to the stated [ssid], using the [passkey] as a WPA, WPA2,
  // or WEP passphrase.
  WiFi.begin(WiFiSSID, WiFiPSK);
  
  // Use the WiFi.status() function to check if the ESP8266
  // is connected to a WiFi network.
  while (WiFi.status() != WL_CONNECTED)
  {
    // Blink the LED
    digitalWrite(LED_PIN, ledStatus); // Write LED high/low
    ledStatus = (ledStatus == HIGH) ? LOW : HIGH;
    
    // Delays allow the ESP8266 to perform critical tasks
    // defined outside of the sketch. These tasks include
    // setting up, and maintaining, a WiFi connection.
    delay(100);
    // Potentially infinite loops are generally dangerous.
    // Add delays -- allowing the processor to perform other
    // tasks -- wherever possible.
  }
}

//function that sets up some initial hardware states
void initHardware()
{
  Serial.begin(9600);
  pinMode(LED_PIN, OUTPUT);
  digitalWrite(LED_PIN, LOW);
}

//this function takes data and posts it to the cloud
int postToPhant()
{
  // LED turns on when we enter, it'll go off when we 
  // successfully post.
  digitalWrite(LED_PIN, HIGH);
  
  // Declare an object from the Phant library - phant
  Phant phant(PhantHost, PublicKey, PrivateKey);
  //These functions build data and field string that will be sent to phant cloud
  phant.add("adcdata", analogRead(ANALOG_PIN));
  phant.add("wifinode", NODE_NUM);
  
  // Now connect to data.sparkfun.com, and post our data:
  WiFiClient client; //declare client object that will post the data
  const int httpPort = 80; //specify port to post through
  
  if (!client.connect(PhantHost, httpPort)) //attempt to connect to phant
  {
    // If we fail to connect, return 0.
    return 0;
  }
 //Send post to phant
  client.print(phant.post());
  
  // Read all the lines of the reply from server and print them to Serial
  while(client.available()){
    String line = client.readStringUntil('\r');
    //Serial.print(line); // Trying to avoid using serial
  }
  
  // Before we exit, turn the LED off.
  digitalWrite(LED_PIN, LOW);
  
  return 1; // Return success
}
 

Monday, September 5, 2016

Combining Arduino, Android, and the Cloud Part 3

In this 3 part series we look at how to create an Android app to monitor and control multiple WiFi enabled Arduinos using the cloud. In part 3 the finale we will look at how to send control data to the cloud using an Android App to control the Arduino WiFi nodes. To download the Android App .aia file to load into MIT App Inventor II use the following link: https://dl.dropboxusercontent.com/u/26591541/CloudHomeAutoEx2.aia


//Arduino MKR1000 Code****************************************************
/*
 This sketch was created for a tutorial called Combining Arduino, Android, and the Cloud Part 3 
 That was presented on the ForceTronics YouTube Channel. This code is public domain for anybody to 
 use or modify at your own risk

 Note that this code was leveraged from the Arduino WiFi101 examples and from a Sparkfun example 
 on using their cloud service Phant
 */


#include <SPI.h>
#include <WiFi101.h>

char ssid[] = "YourNetwork"; //  your network SSID (name)
char pass[] = "YourPassword";    // your network password (use for WPA, or use as key for WEP)
int keyIndex = 0;            // your network key Index number (needed only for WEP)
bool pData = false;  //used to toggle between posting data and getting data

int status = WL_IDLE_STATUS;

//define some constant variables for pins and node number
const int LED_PIN = 6; // Thing's onboard, green LED
const int ANALOG_PIN = A0; // The only analog pin on the Thing
const int NODE_NUM = 2; //node identifier
const char parseKey[] = "stamp";

//define areas for phant cloud address and security keys
const char PhantHost[] = "data.sparkfun.com";
const char pPublicKey[] = "PublicKeyForPosting";
const char pPrivateKey[] = "PrivateKeyForPosting";
const char gPublicKey[] = "PublicKeyForGetting";
const char gPrivateKey[] = "PublicKeyForGetting";
//The following variables are from Phant library created by Sparkfun.
String _pub;
String _prv;
String _host;
String _params;
static const char HEADER_POST_URL1[] PROGMEM = "POST /input/";
static const char HEADER_POST_URL2[] PROGMEM = ".txt HTTP/1.1\n";
static const char HEADER_PHANT_PRV_KEY[] PROGMEM = "Phant-Private-Key: ";
static const char HEADER_CONNECTION_CLOSE[] PROGMEM = "Connection: close\n";
static const char HEADER_CONTENT_TYPE[] PROGMEM = "Content-Type: application/x-www-form-urlencoded\n";
static const char HEADER_CONTENT_LENGTH[] PROGMEM = "Content-Length: ";

//timing for posting to the phant cloud
const unsigned long postRate = 15000;
unsigned long lastPost = 0;

void setup() {
  pinMode(LED_PIN, OUTPUT); //setup LED pin
  digitalWrite(LED_PIN, LOW); //Turn off LED
  Serial.begin(9600);
  while (!Serial) { //Note the code will not cont unless you open serial monitor
    ; // wait for serial port to connect. Needed for native USB port only
  }

  // check for the presence of the shield:
  if (WiFi.status() == WL_NO_SHIELD) {
    Serial.println("WiFi shield not present");
    // don't continue:
    while (true);
  }

  // attempt to connect to Wifi network:
  while (status != WL_CONNECTED) {
    Serial.print("Attempting to connect to SSID: ");
    Serial.println(ssid);
    // Connect to WPA/WPA2 network. Change this line if using open or WEP network:
    status = WiFi.begin(ssid, pass);

    // wait 10 seconds for connection:
    delay(10000);
  }
  Serial.println("Connected to wifi");
  printWifiStatus(); //Print info about the WiFi network that you are connected to
}

void loop() {
  //Delay for set time then post and get data from Phant cloud
  if (lastPost + postRate <= millis())
  {
    if(pData) {
      if (postToPhant()) lastPost = millis();
      else lastPost = millis(); //Even if we fail delay whole cycle before we try again   
    } 
    else {
      if (getFromPhant()) lastPost = millis();
      else lastPost = millis(); //Even if we fail delay whole cycle before we try again 
    }
  }
}

//function that handles posting and getting data from phant cloud
int getFromPhant()

 //Set phant data
 phant(PhantHost, gPublicKey, gPrivateKey);
  
  WiFiClient client; //Create client object to communicate with the phant server

  if (!client.connect(PhantHost, 80)) { //Attempt to connect to phant server using port 80
    // If we fail to connect, return 0.
    return 0;
  }

  //Get data from phant cloud
    client.print(phantGet()); 
    client.println();
    Serial.println("sent get request.....");
   int cTrack = 0; //variable that tracks count to spell stamp
   bool match = false; //tracks when we have a match with "stamp" and we can then get control data
   int pCount = 0; //variable used to track whe we have control data
   while(1) { //loop until we get data and server closes connection
    if (client.available()) { //if data is available from phant server
      char c = client.read(); //read a bite of data from server
      if(!match) { //if true than we have not found the word "stamp" so keep looking
        if(c == parseKey[cTrack]) //check if we have a character match with word "stamp"
        {
          if(cTrack == (sizeof(parseKey)-2)) match = true; //if true it means we found a match for "stamp" in data from phant cloud
          cTrack++; //iterate this count if a character match was found
        }
        else { //if true means no character match so reset count
          cTrack = 0;
        }
      }
      else { //if true it means we found a match to "stamp" and we are ready to get control data
        
        if(pCount == 3) { //if true we are at the point in the data to read control data for node oen
          Serial.print(c);
          int dControl = c - '0'; //convert char data to an int by subtract an ASCII zero
          if(dControl == 1 | dControl == 0) digitalWrite(LED_PIN, dControl); //make sure data is a one or zer and set LED pin with it
        }
        pCount++; //iterate the parse counter
      }
    }

    // if the server's disconnected, stop the client:
    if (!client.connected()) {
      Serial.println();
      Serial.println("disconnecting.");
      client.stop(); //stop client, if you don't have this you will create too many clients and server won't let you connect anymore
      break; //This is how we get out of the loop
    }
   }
  pData = true; //set to true so we post data to cloud next loop
  return 1; // Return success
}

//function used to post data to phant cloud
int postToPhant()
{
  // Declare an object from the Phant library - phant
  phant(PhantHost, pPublicKey, pPrivateKey);
  //These calls build the web communication strings with Phant
  phantAdd("adcdata", analogRead(ANALOG_PIN)); //specify field and data used in that field
  phantAdd("wifinode", NODE_NUM);
  
  WiFiClient client; //Create client object to communicate with the phant server

  if (!client.connect(PhantHost, 80)) { //Attempt to connect to phant server using port 80
    // If we fail to connect, return 0.
    pData = false; //set to false so we get data from cloud next loop
    return 0;
  }

  //Send post to phant server
  client.print(phantPost()); 
  
  // if there are incoming bytes available
  // from the server, read them and print them:
  while (client.available()) {
    String line = client.readStringUntil('\r');
    //Do something with data
  }
  client.stop();
  pData = false; //set to false so we get data from cloud next loop
  return 1; // Return success
}

void printWifiStatus() {
  // print the SSID of the network you're attached to:
  Serial.print("SSID: ");
  Serial.println(WiFi.SSID());

  // print your WiFi shield's IP address:
  IPAddress ip = WiFi.localIP();
  Serial.print("IP Address: ");
  Serial.println(ip);

  // print the received signal strength:
  long rssi = WiFi.RSSI();
  Serial.print("signal strength (RSSI):");
  Serial.print(rssi);
  Serial.println(" dBm");
  Serial.println();
}


//This is from phant library, initializes variables
void phant(String host, String publicKey, String privateKey) {
  _host = host;
  _pub = publicKey;
  _prv = privateKey;
  _params = "";
}

//From phant library, builds string of field and data
void phantAdd(String field, int data) {

  _params += "&" + field + "=" + String(data);

}

//From phant library, builds string to get data from Phant cloud
String phantGet() {
  String result = "GET /output/" + _pub + ".csv?page=1 HTTP/1.1\n";
  result += "Host: " + _host + "\n";
  result += "Connection: close\n";

  return result;

}

//From phant library, builds the string used to post data to phant over web services
String phantPost() {

  String params = _params.substring(1);
  String result;
  //String result = "POST /input/" + _pub + ".txt HTTP/1.1\n";
  for (int i=0; i<strlen(HEADER_POST_URL1); i++)
  {
    result += (char)pgm_read_byte_near(HEADER_POST_URL1 + i);
  }
  result += _pub;
  for (int i=0; i<strlen(HEADER_POST_URL2); i++)
  {
    result += (char)pgm_read_byte_near(HEADER_POST_URL2 + i);
  }
  result += "Host: " + _host + "\n";
  //result += "Phant-Private-Key: " + _prv + "\n";
  for (int i=0; i<strlen(HEADER_PHANT_PRV_KEY); i++)
  {
    result += (char)pgm_read_byte_near(HEADER_PHANT_PRV_KEY + i);
  }
  result += _prv + '\n';
  //result += "Connection: close\n";
  for (int i=0; i<strlen(HEADER_CONNECTION_CLOSE); i++)
  {
    result += (char)pgm_read_byte_near(HEADER_CONNECTION_CLOSE + i);
  }
  //result += "Content-Type: application/x-www-form-urlencoded\n";
  for (int i=0; i<strlen(HEADER_CONTENT_TYPE); i++)
  {
    result += (char)pgm_read_byte_near(HEADER_CONTENT_TYPE + i);
  }  
  //result += "Content-Length: " + String(params.length()) + "\n\n";
  for (int i=0; i<strlen(HEADER_CONTENT_LENGTH); i++)
  {
    result += (char)pgm_read_byte_near(HEADER_CONTENT_LENGTH + i);
  } 
  result += String(params.length()) + "\n\n";
  result += params;

  _params = "";
  return result;
}

//This function convers the ADC level integer value into float voltage value.
//The inputs are the measured ADC value and the ADC reference voltage level
//The formula used was obtained from the data sheet: (ADC value / 1024) x ref voltage
float convertToVolt(float refVal, int aVAL) {
  return (((float)aVAL/1024)*refVal);
}

//this function calculates temp in F from TMP36 temp sensor
//see TMP36 datasheet to understand algorithm used
float calculateTempF(float v1) { 
 float temp = 0;
 //calculate temp in C, .75 volts is 25 C. 10mV per degree
 if (v1 < .75) { temp = 25 - ((.75-v1)/.01); } //if below 25 C
 else if (v1 == .75) {temp = 25; }
 else { temp = 25 + ((v1 -.75)/.01); } //if above 25
 //convert to F
 temp =((temp*9)/5) + 32;
 return temp;
}

//Arduino ESP8266 Code****************************************************
/*
 This sketch was created for a tutorial called Combining Arduino, Android, and the Cloud Part 3 
 That was presented on the ForceTronics YouTube Channel. This code is public domain for anybody to 
 use or modify at your own risk

 Note that this code was leveraged from a Sparkfun example 
 on using their cloud service Phant
 */

// Include the ESP8266 WiFi library. (Works a lot like the
// Arduino WiFi library.)
#include <ESP8266WiFi.h>
// Include the SparkFun Phant library.
#include <Phant.h>

//Set your network name and password
const char WiFiSSID[] = "YourNetwork";
const char WiFiPSK[] = "YourPassword";

//define constants for pin control and node number
const int LED_PIN = 5; // Thing's onboard, green LED
const int ANALOG_PIN = A0; // The only analog pin on the Thing
const int NODE_NUM = 1; //node identifier
const char parseKey[] = "stamp";
bool pData = false;  //used to toggle between posting data and getting data

//declare phant address and security keys
const char PhantHost[] = "data.sparkfun.com";
const char pPublicKey[] = "PublicKeyForPosting";
const char pPrivateKey[] = "PrivateKeyForPosting";
const char gPublicKey[] = "PublicKeyForGetting";
const char gPrivateKey[] = "PublicKeyForGetting";

//specify the rate that you post data to cloud
const unsigned long postRate = 15000;
unsigned long lastPost = 0;

void setup() 
{
  initHardware(); //setup arduino hardware
  connectWiFi(); //Connect your WiFi network
  digitalWrite(LED_PIN, HIGH);
}

void loop() 
{ //loop until it is time to post data to phant cloud
  if (lastPost + postRate <= millis())
  {
    if(pData) {
      if (postToPhant()) lastPost = millis();
      else lastPost = millis(); //Even if we fail delay whole cycle before we try again   
    } 
    else {
      if (getFromPhant()) lastPost = millis();
      else lastPost = millis(); //Even if we fail delay whole cycle before we try again 
    }
  }
}

//function used to connect to WiFi network
void connectWiFi()
{
  byte ledStatus = LOW;
  // Set WiFi mode to station (as opposed to AP or AP_STA)
  WiFi.mode(WIFI_STA);
  // WiFI.begin([ssid], [passkey]) initiates a WiFI connection
  // to the stated [ssid], using the [passkey] as a WPA, WPA2,
  // or WEP passphrase.
  WiFi.begin(WiFiSSID, WiFiPSK);
  
  // Use the WiFi.status() function to check if the ESP8266
  // is connected to a WiFi network.
  while (WiFi.status() != WL_CONNECTED)
  {
    // Blink the LED
    digitalWrite(LED_PIN, ledStatus); // Write LED high/low
    ledStatus = (ledStatus == HIGH) ? LOW : HIGH;
    
    // Delays allow the ESP8266 to perform critical tasks
    // defined outside of the sketch. These tasks include
    // setting up, and maintaining, a WiFi connection.
    delay(100);
    // Potentially infinite loops are generally dangerous.
    // Add delays -- allowing the processor to perform other
    // tasks -- wherever possible.
  }
}

//function that sets up some initial hardware states
void initHardware()
{
  Serial.begin(9600);
  pinMode(LED_PIN, OUTPUT);
  digitalWrite(LED_PIN, LOW);
}

//function that handles posting and getting data from phant cloud
int getFromPhant()

 //Set phant data
 Phant phant(PhantHost, gPublicKey, gPrivateKey);
  
  WiFiClient client; //Create client object to communicate with the phant server

  if (!client.connect(PhantHost, 80)) { //Attempt to connect to phant server using port 80
    // If we fail to connect, return 0.
    return 0;
  }

  //Get data from phant cloud
    client.print(phant.get()); 
    client.println();
   int cTrack = 0; //variable that tracks count to spell stamp
   bool match = false; //tracks when we have a match with "stamp" and we can then get control data
   int pCount = 0; //variable used to track whe we have control data
   while(1) { //loop until we get data and server closes connection
    if (client.available()) { //if data is available from phant server
      char c = client.read(); //read a bite of data from server
      if(!match) { //if true than we have not found the word "stamp" so keep looking
        if(c == parseKey[cTrack]) //check if we have a character match with word "stamp"
        {
          if(cTrack == (sizeof(parseKey)-2)) match = true; //if true it means we found a match for "stamp" in data from phant cloud
          cTrack++; //iterate this count if a character match was found
        }
        else { //if true means no character match so reset count
          cTrack = 0;
        }
      }
      else { //if true it means we found a match to "stamp" and we are ready to get control data
        
        if(pCount == 1) { //if true we are at the point in the data to read control data for node oen
          int dControl = c - '0'; //convert char data to an int by subtract an ASCII zero
          if(dControl == 1 | dControl == 0) digitalWrite(LED_PIN, dControl); //make sure data is a one or zer and set LED pin with it
        }
        pCount++; //iterate the parse counter
      }
    }

    // if the server's disconnected, stop the client:
    if (!client.connected()) {
      client.stop(); //stop client, if you don't have this you will create too many clients and server won't let you connect anymore
      break; //This is how we get out of the loop
    }
   }
  pData = true; //set to true so we post data to cloud next loop
  return 1; // Return success
}

//this function takes data and posts it to the cloud
int postToPhant()

  // Declare an object from the Phant library - phant
  Phant phant(PhantHost, pPublicKey, pPrivateKey);
  //These functions build data and field string that will be sent to phant cloud
  phant.add("adcdata", analogRead(ANALOG_PIN));
  phant.add("wifinode", NODE_NUM);
  
  // Now connect to data.sparkfun.com, and post our data:
  WiFiClient client; //declare client object that will post the data
  const int httpPort = 80; //specify port to post through
  
  if (!client.connect(PhantHost, httpPort)) //attempt to connect to phant
  {
    // If we fail to connect, return 0.
    return 0;
  }
 //Send post to phant
  client.print(phant.post());
  
  // Read all the lines of the reply from server and print them to Serial
  while(client.available()){
    String line = client.readStringUntil('\r');
    //Serial.print(line); // Trying to avoid using serial
  }
  pData = false; //set to false so we get data from cloud next loop
  return 1; // Return success
}